Bathroom Ceiling Lights

One of the common questions our customers ask us is related to bathroom lighting, and quite a few of them ask us about IP20-rated lights, and whether they are suitable for use in the bathroom. Are IP20 rated light fittings suitable for use in the bathroom? Can I install an such a light in the bathroom? Questions like these are posed every day, especially since there are some amazing such ceiling lights or wall lamps that the customers really love, and they would like to install them in the bathroom. Let's explore this question together and see what is the correct answer to, Are IP20-rated Lights Suitable for Bathroom Lighting?Note: at Sparks we sell a wide range of IP20 rated lights, IP44 rated light fittings, and IP65 rated lights.IP Rating and Bathroom Zones - Rules and RegulationsWhen installing anything in the bathroom in the UK we need to know the current regulations, which are contained in the 18th Edition Wiring Regs. You may not know them, but it is good to know what wiring regulations apply to installing lights and light fittings in the bathroom, otherwise we put ourselves in great danger, because water and electricity should never mix. Electrical hazards and electrical short circuits due to the mixing of water and electricity should be avoided at any cost since they pose great danger to human life. So what do the wiring regulations say about lighting in the bathroom? The 18th Edition Wiring Regulations define certain bathroom zones - see the image.Note: we have introduced the IP ratings, IP zoning, and Bathroom Zones - see the articles linked. The bathroom zones are three: Zone 0 is the area inside the bathtub or in the shower. There is a lot of splashing water and even more, it can be submerged in water, so special light fittings need to be installed here.Zone 1 is the area above and around the bathtub and the shower, up to 2.25m above the floor. This area is also under the reach of splashing water. Zone 2 is the area of up to 60cm beyond the bathtub edge, basically 60cm outside zone 1. There is some reach of water here, but not as much. The outside zone, the zone outside all these areas, where in general there is no splashing water - some call it "zone 3" while others just call it "the zone outside zones 1 and 2".The current wiring regulations state that specific IP-rated light fittings can be installed in the three zones for the protection of human life. The following IP ratings are recommended:In Zone 0 it is recommended to use IP67, total immersion-proof light fittings, and 12v (low voltage) light fittings are recommended. For our safety, it is not recommended to install any light fitting that is under IPx7 in zone 0.In zone 1 it is recommended to use light fittings having an IP rating of minimum IP45, and IP65 light fittings are warmly recommended in this zone, since water can still reach the light fittings. In zone 2, the area stretching 0.6m outside the perimeter of the bath and up to a height of 2.25 from the floor, it is recommended to use light fittings that have an IP rating of IP44, which are protected from water drops. In the zones outside these three, no IP rating is required, so an IP20-rated fitting can be safely installed. However, for safety reasons, it's best to have IP44-rated light fittings outside of the bathroom zones. IP20 Lights - are they good for the Bathroom?Coming back to our original question, are IP20 rated lights suitable for installation in the bathroom? See the picture above: can this Kymi 220 Plaster Wall Light (Paintable) Ridged Semi-Cylindrical Fitting be installed in the bathroom?Buy the Kymi 220 Plaster Wall Light We may like its finish and shape, but is it safe to be in the bathroom? Based on the current wiring regulations, IP20 rated lights can be installed outside the bathroom zones, that is, away from the reach of splashing or dripping water. Depending on the size of the bathroom, there are many spaces and areas where IP20-rated wall lights or ceiling lights can be installed. These areas are not reached by water jets nor are they at the risk of being splashed or sprinkled with water, so IP20 rated light fittings can safely be installed. However, for the sake of safety, it is best to use IP44-rated lights in the bathroom, even outside the bathroom zones. If you want to be on the safe side, we warmly recommend IP44-rated ceiling lights and wall lamps in the bathroom, outside the bathroom zones. Note: we at Sparks are not qualified to offer professional advice, but we can apply the current regulations and offer advice based on our experience. Before installing any light fitting in the bathroom, please consult with a registered electrician - send them the link to where the light fitting can be viewed, and they will advise. If you are planning to clean the bathroom light fitting with a spray of water or maybe wash it, it is best to have the light fittings rated to a minimum IP65. If there is no reach of splashing water where the light fitting is, and it is outside the bathroom zones defined in the wiring regulations, such lights are suitable. In Conclusion: Always Be Safe in the BathroomIn conclusion, it is entirely up to you when installing IP20 rated lights in the bathroom - outside the bathroom zones. For example, the Ortona Twin Matt Black Bathroom Wall Lamp with Opal-Glass Globe Shades IP44 can safely be used in the bathroom, since it is IP44-rated.Buy the Ortona Twin Matt Black Wall Lamp We would advise staying on the safe side, that is, using IP44-rated light fittings even outside the bathroom zones. You never know, with the steam rising from the bathtub, the vapours of air coming out of the shower, water can reach the light fittings located outside the bathroom zones, and electrical hazards can happen. And whatever you do in the bathroom, always consult a registered electrician to both install and advise on the light fittings you are allowed to install there. 

You may have heard of Part P of the Building Regulations; in this article, we want to delve into what it covers, how it affects us, and what needs to be done in case of electrical wiring alterations at home. In 2005 the UK Government introduced electrical safety rules into the Building Regulations for England and Wales. According to these regulations, most fixed electrical installation work in homes must meet the Building Regulations (by law).Continue reading this guide to find out more about:What is Part P of the Building Regulations?What are the Special Locations covered by Part P?How to make sure Electrical Work Meets the Requirements of Part P?How does Part P of the Building Regulations affect Me?What To Do when Electrical Installation Work needs to be Carried out in My Home?Why use a Government-approved Part-P Electrician?Part P of the Building Regulations - Further information In particular, Part P of the Building Regulations states that anyone who carries out electrical installation work in a home has to make sure that this work is designed and installed to protect people from electric shocks and fire. For example, if you want to make any changes to an existing electrical installation, including any parts that have been rewired, all such works need to be done by a Part P-certified competent person. Then, in 2013 further changes were introduced, reducing the range of electrical installation work that is notifiable; these new regulations removed some requirements in the kitchen and outdoors. What is Part P of the Building Regulations?Part P of the Building Regulations makes sure that, in the design and installation of electrical installations in the home, people are protected when operating, maintaining, and altering the installations from fire and injury. In particular, in areas and zones in the bathroom, there has to be appropriate protection against mechanical and thermal damage, and the electrical installations and wiring need to be done in a safe way, so as not to present an electric shock or fire hazard to people. Part P of the Building Regulations in particular addresses electrical work and rewiring done in the bathroom, any addition or alteration to an existing circuit in a special location, the installation of a new circuit, and the replacement of a consumer unit; all these need to be done by a competent electrical person. What is non-notifiable is any other work such as additions or alterations to existing installations outside special locations, maintenance, replacement, and repair work.Buy Hager Consumer Units At Sparks we distribute a wide range of Hager Consumer Units (with the required RCDs, MCBs, and RCBOs) and BG Consumer units; these need to be installed by a registered electrician.What are the Special Locations covered by Part P?Here are the special locations covered by Part P of the Building Regulations A room that contains a bath or a showerThe space surrounding a bath tap or showerhead where the space extends vertically from the finished floor level to a height of 2.25 metres or the position of the showerhead where it is attached to a wall or ceiling at a height higher than 2.25 metres from that level or horizontally where there is a bathtub or shower tray, from the edge of the bathtub or shower tray to a distance of 0.6 metresWhere there is no bathtub or shower tray from the centre point of the showerhead where it is attached to the wall or ceiling to a distance of 1.2 metres,A room containing a swimming pool or sauna heater.Furthermore, Part P of the Building Regulations applies to electrical installations in the following locations:A dwelling-house or a flat and parts of the installation that are outside the dwelling (fixed lighting and air conditioning units attached to outside walls, fixed lighting and pond pumps in the garden, etc), in outbuildings (such as sheds, detached garages, domestic greenhouses, etc). Common access areas of blocks of flats such as corridors and staircasesShared amenities of blocks and flats such as laundries, kitchens, and gymnasiumsBusiness premises (other than agricultural buildings) connected to the same meter as the electrical installation in a dwelling (for example, shops and public houses below flats).The Part P of the Building Regulations does not apply to electrical installations in locations such as:Business premises in the same building as a dwelling but with separate meteringLocations that supply the power for lifts in blocks of flats (Part P applies to lift installations in single dwellings).Buy Bathroom Ceiling LightsNote: We at Sparks do not offer advice on installing the bathroom ceiling lights, shower downlights, and shaver sockets; we only sell these, and you need to get a registered electrician to have them installed.How to make sure Electrical Work Meets the Requirements of Part P?All the electrical installations in a home, garden, conservatory or outbuilding must meet the current Building Regulations. However, any electrical work done in the special areas defined by Part P of the Building Regulations needs to be done by an electrical competent person, a Part P registered electrician. The person responsible for making sure that electrical work meets the requirement of Part P of the Building Regulations is the electrician.Buy the Denia Bathroom Ceiling Light If any electrical work is done by a DIY or freelancer who is not registered, local authorities can make homeowners or landlords remove or alter any work that doesn't meet the Building Regulations.How does Part P of the Building Regulations affect Me?The Part P of the Building Regulations requires that a registered electrician is used to do safe electrical installation work at home, especially in the special areas defined by Part P. Their work will meet the UK national standard, BS 7671 (requirements for electrical installations). When they finish their work, the registered electrician will provide you withAn Electrical Installation Certificate or Minor Work Certificate that confirms that the work meets BS 7671; andA Building Regulations Compliance Certificate that confirms that the work meets the Building Regulations.What To Do when Electrical Installation Work needs to be Carried out in My Home?If electrical installation work needs to be carried out in your home, you need to make sure you know the current building regulations and act according to them. This means that you need to either tell your local authority building control about the installation work before it starts or employ an electrician who is registered with one of the Government-approved Part P schemes. You can find a registered electrician via this link. In the UK there are some defined competence self-certification schemes such as the Association of Plumbing and Heating Contractors (APHC), BESCA, Blue Flame Certification, NAPIT Registration Ltd and Certsure LLP trading as NICEIC and ELECSA, aimed at those who carry out installation work only as an adjunct to or in connection with the primary activity of their business. There is only one body currently authorised to operate third-party certification which is NAPIT.Buy Bathroom Pull Cord Switches At Sparks we sell a wide range of Bathroom Lights and Bathroom Wiring Accessories such as shaver sockets, pull cord switches, etc; all these need to be installed by a government-approved part-p electrician.Why use a Government-approved Part-P Electrician?Some homeowners may think that they can undertake any electrical work in their house, no matter what it is; they like to tinker with things and DIY is their hobby. However, when it comes to special locations in the home and around the home, it is best to be safe when doing any electrical work or installation. Here are some of the advantages of using a registered electrician who is part-P approved to do the electrical installation work:You won't have to pay any building-control charges.The registered electrician can deal with everything for you.The part-P electrician will arrange for you to receive a certificate that confirms the work meets Building Regulations.You have access to a formal complaints procedure if the work doesn't meet Building Regulations.You can choose to take out an insurance-backed guarantee when you have the work done, and you can make a claim if the work is later found not to meet Building Regulations.Part P of the Building Regulations - Further informationThis article was inspired by many of the following sources below, which we recommend for further reading:Part P Of The Building Regulations, via Electrical Safety First.Electrical safety: Approved Document P - Building Regulation in England covering electrical safety in dwellings. Via, the Building Regulations government page.Approved Document P: electrical safety, dwellings - the PDF file of the regulations.Part P Building Regulations via IET, the Institution of Engineering and Technology.