Aurora Lighting Fire Rated Fixed Downlights

Downlights are a lovely way to brighten up your home. They are often small and recessed, making them convenient to place in any part of your home that you feel is a little too dim. However, poorly installed downlights are the cause of a substantial number of fires in homes every year. The rise in popularity of LED lights has led to many people attempting to replace their old recessed ceiling lights themselves. DIY can always be risky, especially when you are handling electronics. Sparks advises you seek the help of a registered electrician to do this particular job. In this article, Sparks will take you through how to safely replace downlights and achieve bright energy-efficient lighting anywhere across your home. What is a downlight, and what are the different kinds? Downlights are a type of recessed luminaire. They are installed in hollow openings, usually in ceilings, as they cast their light downwards. Having a light fixture installed in a hollow recess makes the light appear to be part of the ceiling itself. This is opposed to suspended or wall lights which will hang down, or stay separate from the ceiling. Downlights operate at mains voltage (230 Volts) or are powered by a transformer at low voltage (12 Volts). These low-voltage lights are often given the acronym Extra-Low Voltage (ELV) or Safety Extra-Low Voltage (SELV). At Sparks, we have a wide range of low-voltage downlights, many of which also have a high IP rating for mounting in the bathroom or shower. ‘Fire rated’ (FR) downlights have built-in fire protection that seals the downlight if a fire breaks out in the room below. This will stop - or hinder - the spread of fire and smoke into other areas. The trusted Electrical Safety First (ESF) recommends the use of Fire Rated downlights, for any installation. They also advise that they are fitted with aluminum reflector lamps to ensure fire and excessive heat is kept out of any gaps.Buy Fixed Downlights at Sparks Questions you may have about Fire-Rated downlights This Fire Rated Void Round 80 LED Downlight can be purchased from this list here.What’s the purpose of a fire-rated downlight?The purpose of a Fire Rated downlight is to ensure that there are no weak spots in your ceiling. This ensures that the integrity of the structure of a building is maintained in all areas.When and where should FR downlights be fitted?They are most often fitted by designers in avenues of escape, for instance, hallways. Fire Rated downlights must always match the fire rating standard of the structure they are fitted on to. The rare exception is with false ceilings i.e. in open plan offices.How is downlight quality and effectiveness tested?A responsible manufacturer will seek to have their products constructed to meet certain test criteria, and pass very stringent live fire tests. These tests are set by the British Standards Organisation or their equivalent European tests, and they must receive a ‘pass’ certificate.Astro Lighting Void Round DownlightsThinking of installing new downlights? Here are some Safety Tips Sparks would encourage you to use a registered electrician to install your downlighters. You should keep the manufacturer's instructions for your new downlights in a safe place for future reference. Here is a brief list of other steps to follow when installing downlights: Thoroughly read and follow the manufacturer's instructions. Always ensure your mains-powered electricity is switched off before changing the lamp. Look at the packaging and the downlighter for details of the correct replacement lamps. Do not exceed the maximum number of wattage allowed. Don't fit a cool beam (or ‘dichroic’) reflector lamp unless the downlight is specifically designed for use with that lamp type. If in any doubt, just fit them with standard aluminium reflector lamps. Check to see that the lamp holder is not damaged, scorched, or corroded. If it is, then do not fit the lamp and seek help from a registered electrician. Checking your existing downlights: Safety tips If you just want to check that the downlights you are currently using are safe, you can take the following steps: Look for visible markings on downlights which indicate lamp wattage and lamp type. Check the recessed ceiling lights and their surroundings for signs of discoloration or scorching caused by overheating. Make sure that downlights installed in floor and ceiling cavities have enough space around them. Ensure that downlights are not in close proximity of loft insulation or other combustible materials. Check that your downlights are not placed near furniture, curtains or similar flammable items. Make sure you haven’t fitted ‘dichroic’ lamps in lamp holders designed for use with aluminum reflector lamps. If you have, then replace them with the correct type. We hope this guide has given you comprehensive information on how to safely handle your downlights. This applies to instances where you are replacing them, or simply checking that the ones you have installed are safe.

Some of the best fire-rated downlights, tested and approved according to the highest UK standards, are those manufactured by Aurora Lighting. Recently they have posted a blog post concerning the requirements, the specifications, and the testing of their fire-rated lights, and we deem it necessary to glean bits and pieces of very useful information for you, our customer and visitor. Stay tuned as you read the article: the best bits are at the end! Why do we Need Fire Rated Downlights? First of all, why do we need to install fire-rated downlights? The Building Regulations in the UK require fire protection for certain types of premises. You can check out Document B (fire safety, approved document, see it online here), where we see that residential homes, flats, sheltered housings, health care premises, schools, universities, student accommodations, shops, assembly and recreational buildings, etc all need to have fire protection recessed lights. Depending on the building construction, most ceilings in houses with more than one floor needs to have fire-rated lights. What's so Special about Fire Rated Lights? So, what do the fire-rated downlights do? If there's a fire on a certain level of a building, the principle of the fire-rated downlights is that they don't allow the spreading of the fire to the floors or spaces above. This means that the downlights have a special construction that blocks the spreading of the fire and, instead of weakening the fire protection of the ceiling, it "fills the hole" in the ceiling to protect the space above. Read more about the fire-rated downlights here.Fire rated Lights at SparksWhat Fire-Rated Downlight Do I Need? There are different types of fire-rated downlights, and there are different requirements for the various types of buildings and types of construction. The basement for instance, if it is residential, needs a 30-60 minutes fire rating, while the basement in a flat or any other residential building needs 90 minutes fire protection. When it comes to the ground level and above, depending on the height of the floor, in general in the residential buildings you need 60 minutes fire rated downlights, and in flats and other residential buildings you sometimes need a fire protection for up to 120 minutes. Check out the diagram supplied by Aurora above to find out more precise details. How do these Fittings Work and How are They Tested? The fire-rated downlights contain a special intumescent material which, in case of fire and extreme heat, expands and enlarges until it bridges the downlight can's ventilation hole. The maintaining of the fire resistance of the ceiling is integral when the intumescent material expands and blocks the expansion of the fire on the floor/space above the ceiling. In a nutshell, see below a picture describing this process. How does Aurora Lighting test its fire-rated downlights? Check out the picture supplied by them below and see a little about the process of testing: the test furnace, inside the furnace, the ceiling construction, the installation, board the ceiling, begin the testing, test monitoring, the success of the test, and the final results - PASS! In conclusion, a big thank you to the good people at Aurora Lighting for their explanations, and don't forget to visit the fire rated ceiling lights section on our website at to see a complete range of fire protection downlights from Aurora.Buy Fire Rated Downlights at Sparks

In our store you may have noticed that we have a range of fire protection ceiling lights. You may also have some questions about these items, and we are happy to answer a few of them right now on this blog. This article tries to answer four simple questions you always wanted to ask about the fire-rated ceiling lights, but maybe you were afraid to ask... 1. What is a Fire-Rated Ceiling Light? A fire-rated light fitting completely seals the opening that was made in the ceiling when it was installed. That means sealing even the tiny hole that was necessary in order to pass electrical wires through. To achieve this, many fire-resistant ceiling lights incorporate an amount of intumescent material that expands in response to heat and completely seals that opening. This fully protects your house in case of a fire. 2. Why should I invest in a fire-rated light? Regulations state that any multi-storey building must incorporate fire-proof materials between its floors to slow the spread of fire. Plasterboard is sufficiently fire-resistant: a single sheet will withstand a fire for around 30 minutes. This offers a longer time to escape. Further, plasterboard sheets can be layered together for an extra 30 minutes per sheet: in most domestic properties, the ceilings are fire resistant for up to 60 minutes, but in high-rise buildings and commercial buildings, 90 minutes may be necessary. So fireproof light fittings need to be rated for installation in 30, 60 or 90-minute ceilings. Be warned, however, that a 90-minute rated fitting may not be suitable for use in a 30 or 60-minute-rated ceiling, and vice versa. If it is not rated, the manufacturer has not tested the light for that use. Light fittings should only be used in the situations for which they are specifically rated. 3. What official standards are available? BS 476-20 (1987) outlines the method for testing fire-resistant construction materials and covers most of the important facts. However, a couple of additions have since complicated matters. Part E also mandates resistance against sound, so fire-resistant ceiling lights are also acoustically rated, which means they prevent the passage of sound through the opening as well as fire. And since 2010, Part L has required at least 25% of the lighting in a property to be energy-efficient. 4. Where can I buy fire-rated ceiling lights? Luckily, we sell both acoustic-rated and L1-compliant ceiling lights! We also stock waterproofed IP65-rated fire protection lights that can be used in the bathroom and kitchen, as well as a lot of other items. Above: Aurora Sola i9 range of fire-rated ceiling downlights. Visit the Fire Protection Ceiling Lights section to see the full range available, some of which also come in a different finish while others have a high IP rating for water and dust protection.Fire Protection Downlights

Do you need a fixed recessed ceiling downlight? The twist and lock Aurora AU-DLM356 offers you a white or satin nickel downlight - at a cheaper price! Do you need an adjustable recessed ceiling light? The adjustable twist and lock Aurora AU-DLM357 gives you a satin nickel or white option - for less than anywhere else! These two ranges of recessed ceiling lights from Aurora Lighting are manufactured according to the highest specifications and use a GU10 lamp up to 50W. These small-size downlights are ideal for office lighting, bedroom lights, kitchen ceiling downlights, living room recessed spotlights, etc. Not for use in the bathrooms, this range of Aurora downlights is great for sitting anywhere in the house. Cheaper Aurora Fixed / Adjustable Downlights - Features Ceiling recessed light: interior downlights; Extended spring fixing posts allow installation in double-thickness plasterboard; Full range of designer accessories available to customize your installation & create varied lighting effects; Dimensions: Cut Out Diameter 70 mm, Overall Diameter 80 mm, Recess Depth 110 mm; Lamp Base: GU10 lamp; Material: Aluminium; Positional Adjustment: Fixed or adjustable; Input Voltage: 240V, mains voltage lamp; Lamps Included: No, the lamp is not included; Dimmable: Yes, dimmable downlight; Finish: satin nickel or white downlights; Product Weight: 0.113 Kg; Warranty: 5 Year Guarantee Aurora Twist and Lock Downlights - Available Models The Aurora DLM356 Fixed Recessed Ceiling Lights - the Aurora DLM356W (white fixed downlights) and DLM356SN(satin nickel fixed downlights), fixed / non-adjustable ceiling downlights in different finishes. The Aurora DLM357 Adjustable Recessed Ceiling Lights - the Aurora DLM357W (white adjustable downlights) and DLM357SN(satin nickel adjustable downlights), adjustable ceiling downlights in different finishes.Aurora Ceiling Downlights at Sparks

Downlighters are one of the most modern and attractive ways to brighten up your home, but choosing the wrong downlighter, incorrectly installing it, or fitting the wrong lamp can pose a serious fire risk. The guide below gives advice on how to prevent your downlighters from becoming a fire hazard (whether Fixed Ceiling Downlights or Adjustable Ceiling Downlights). Read the first part below and the second part - Advice for Downlighter Safety(2): reflector types and checking your existing downlighters. Advice for Downlighter Safety The ceiling downlighters (ceiling recessed lights, whether adjustable downlights, fixed downlights, or Fire Rated Downlights) operate at mains voltage (230 Volts) or are powered via a transformer at extra-low voltage (12 Volts). Extra-low voltage (ELV) downlighters are often described as “low voltage” on product packaging. Downlighters may also be described as ‘Fire rated’. This means they have in-built fire protection that completely seals the downlighter in the event of fire in the room below, to prevent the spread of fire and smoke into other areas. For all downlighters installed into a ceiling, it is recommended to use of ‘fire rated’ downlighters fitted with ‘aluminium’ reflector lamps (see ‘Different lamp types’) to ensure fire and excessive heat are kept out of cavities. Also, where a downlighter is likely to be covered with thermal insulation in the cavity, it’s important to choose a downlighter that will operate safely under these conditions. Are You Thinking of Installing New Downlighters? It is recommended that you use a registered electrician to install your downlighters and that you keep the manufacturer’s instructions in a safe place for future reference, such as when you need to replace a lamp. When fitting replacement lamps it is good to pay attention to: Read and follow the manufacturer’s instructions; Check the packaging and the downlighter for details of correct replacement lamps and do not exceed the maximum allowed wattage; Always switch off the electricity before changing a lamp; Don’t fit a dichroic (cool beam) reflector lamp unless the downlighter is specifically designed for use with that type of lamp. If in doubt, fit only aluminium reflector lamps (see ‘Reflector types’ in the next article); If the lampholder is damaged, scorched or corroded, do not fit the lamp, and seek advice from a registered electrician. Read the second part of this article via, Advice for Downlighter Safety(2): reflector types and checking your existing downlighters.Buy Fire Rated Downlights at Sparks

Read the first part of the article via, ESC advice for Downlighter Safety(1): types of downlighters and tips for installing new downlighters.In this article you can find out more information regarding the types of lamps and reflectors a downlighter takes (whether a fixed downlight or an adjustable downlight), some of the markings found on the downlighters, and some tips for checking your existing downlighters. Different Downlighter lamp types Twist and lock Mains (230 Volts) Push fit ELV (12 Volts) Downlighter Reflector typesThe dichroic and aluminium halogen lamps operate differently from each other but appear identical. It is possible to fit either type in an extra-low voltage downlighter. However, fitting the wrong lamp type can cause overheating, so it’s important to choose the correct type. The type of lamp determines which way the heat generated by the lamp is reflected. Dichroic or cool beam Reflects visible light forwards while allowing radiated heat to pass out of the back of the lamp – to be used in downlighters specifically designed for their use only. Aluminium Reflects both the visible light and most of the heat forwards out of the front of the lamp. Markings to look for on Downlighters Do not use ‘cool beam’ dichroic reflector halogen lamps in this downlighter. Minimum distance from lighted objects. Only ‘self-shielded’ lamps can be fitted in this downlighter. The majority of halogen lamps have a protective shield, which blocks UV (ultraviolet) radiation and protects against the risk of the lamp shattering. Lamp (or transformer) is not suitable for use with a dimmer switch. Tips for Checking Your Existing Downlighters Check for visible markings on downlighters indicating lamp wattage and lamp type Check downlighters and their surroundings for signs of overheating such as curled labels and discoloration or scorching Ensure that downlighters installed in floor and ceiling cavities have sufficient space around them Ensure that downlighters (and associated transformer where fitted) are not in contact with or covered by loft insulation or combustible material unless they are designed to operate safely in those conditions. Check that downlighters are not installed near furniture, curtains or similar combustible items If dichroic (cool beam) lamps are fitted in downlighters designed for use with aluminum reflector lamps only, replace them with the correct type - look for the symbol indicating no use of ‘cool beam’ lamps! # In this case, you need to consider using low energy lamps, such as compact fluorescent lamps (CFL) or light emitting diode lamps (LED), as they produce less heat than a traditional tungsten halogen lamp and so reduce the risk of fire. They also use less electricity. Tips - Safe disposal of the downlighter lamps Some downlighter lamps, such as compact fluorescent lamps (CFL), displaying the crossed-out ‘wheelie bin’ symbol, must not be disposed of in general household waste. Take the lamp to a recycling facility that accepts electrical products. Check with your Local Authority for your nearest recycling centre. This article is the second part of the Guide to Downlighter Safety - read the first part, Advice for Downlighter Safety(1): types of downlighters and tips for installing new downlighters.Buy Downlighters at Sparks

Many of our customers love the downlights on our website, but when they take a closer look at what they need, they realise they need fire rated downlights. Before purchasing any downlights, it is best to know what you need - what are the regulations, what is the requirement, and what are the key considerations. In this article, we would like to go through the main key considerations when purchasing fire rated downlights as Sparks. Continue reading this guide to find out more about:What are Fire Rated Downlights?Are Fire Rated Downlights Required?Key Considerations when Buying Fire Rated DownlightsMaintaining the Fire Rating for the CeilingJoist TypesStandards and CertificationInstallation & ComplianceWhat about Testing and using Fire Hoods?Best Practices Regarding Choosing and Installing Fire Rated DownlightsWhat are Fire Rated Downlights?Fire-rated downlights are recessed lighting fixtures specifically designed to restore the fire integrity of ceilings when a hole is cut for installation. Without them, the ceiling's fire resistance—typically tested for 30, 60, or 90 minutes—can be compromised. These lights include a sealed steel body and an intumescent gasket or pad that expands under high temperatures, effectively sealing the gap and slowing fire spread.Are Fire Rated Downlights Required?We need to realise that fire rating is a classification of complete ceiling construction, not just of individual elements. Under Part B (Fire Safety) of UK Building Regulations (Approved Document B, volumes 1 & 2), any opening in a fire-resistant ceiling must be fire-stopped to prevent rapid fire spread between compartments. Recessed downlights puncture this barrier, so fitting a fire-rated version ensures the ceiling’s integrity is maintained.In residential settings, a 30-minute rating is generally required between living spaces, while 60-minute (houses with loft conversions or three-storey builds) or 90-minute (commercial properties, high-risk areas, or top floors) ceilings require accordingly rated fixtures.Note: the fire rating is invalidated if a product has not been tested and certified in combination with other key elements of the proposed ceiling construction, such as joist type or luminaire spacing.Buy Fire Rated DownlightsKey Considerations when Buying Fire Rated DownlightsMaintaining the Fire Rating for the CeilingUK ceilings are classified by their construction type, and here are the tested ceiling constructions:30 minutes: Single layer 12.5 mm plasterboard on timber joists (~600 mm centres). 600mm joist centres, single layer 15mm Type A or Type F gypsum wallboard60 minutes: Double-layer plasterboard (2×15 mm) on timber (~600 mm centres). 600mm joist centres, double layer 12.5mm Type F gypsum Fireline90 minutes: Double-layer plasterboard on closer-spaced (~450 mm centres) joists. 600mm joist centres, triple layer 12.5mm Type F gypsum Fireline.Joist TypesBecause there are new joist options introduced in recent years, distance spanning has advanced, and so has weight saving and practicality. However. Updated test certificates are necessary in order to ensure product compatibility. Here are the joist types and what they are (according to Astro Lighting):1. Solid Timber JoistsSolid Timber Joists are a traditional method of domestic floor construction and remain ideal for smaller projects where relatively short spans are involved. Solid Timber Joists are typically made from softwood and are available in a range of twelve strength ratings, with C16 and C24 being the most common options.2. Metal Web Joists (or Posi Joists)Metal Web Joists (or Posi Joists) include an open central section allowing for easy installation of services. Metal Web Joists are constructed from a top and bottom stress-graded timber cord, joined with high-strength open metal web sections on either side of the top and bottom timber flanges.3. I-JoistsI-Joists (or I-Beams) are strong, lightweight engineered wood beams with an "I" shape cross-section and are most commonly found in new build properties. I-Joists consist of a top and bottom laminated or solid wood flange combined with a tall vertical plywood or OSB (Oriented Strand Board) web.Please note: The fire rating for I-Joists from one manufacturer cannot automatically be assumed to apply to those from others. However, NHBC Building Control may accept certification to show compliance in certain cases where important testing elements are similar or more demanding.The ceiling opening made for a recessed luminaire can weaken the overall fire barrier; therefore, the spacing of downlights or other luminaires, as well as minimum distances from other ceiling features, is defined in order to obtain the fire safety rating. It is recommended to review the details of each product certification in a careful way, for it is the responsibility of the installer to ensure compliance with the relevant regulations. Fire-rated downlights must be tested to match these ceiling types and fire durations, often under BS 476 21 or BS-EN-1365-2 standards. They must also align with relevant joist material, including solid timber, i-joists, or steel-web joists, per NHBC guidance. Standards and CertificationThe approved light fittings must carry recognised marks: BS-EN-60598-2-2, CE/UKCA, and evidence of independent testing (BRE Global, NHBC). Installation & ComplianceOnly recessed downlights require fire rating—surface-mounted types do notAll cutting and fitting must preserve the ceiling’s rating; improper holes or oversized apertures void complianceUse insulation-coverable downlights if placing insulation material above themManufacturers recommend professional installation under BS-7671 / Part-P (domestic electrical safety regulations)Please avoid opting for generic non-rated downlights and fire hoods as substitutes—hoods don’t meet regulatory standards unless they’re specifically certified, and it’s generally safer to use fully tested fire rated fittingsWhat about Testing and using Fire Hoods?The manufacturers who make fire rated downlights know the standards according to which these luminaires need to be tested. For example, the fire rating test conditions require suspending a complete ceiling structure above a 4x3 meter furnace, and then subjecting it to a predetermined time and temperature fire curve for 30, 60, and 90 minutes. Then, the fire rating of the ceiling is established after the full test period has elapsed, if the declared integrity of the structure is confirmed to have remained intact.Fire hoods: Some prefer using fire hoods instead of buying a fire rated downlight. A fire hood is a flexible cover made from fire-resistant material that can be installed in combination with non-fire-rated downlights or luminaires in order to maintain the integrity of a fire-rated ceiling. Buy Fire Hoods at SparksBest Practices Regarding Choosing and Installing Fire Rated DownlightsSelect the correct rating: match downlight to ceiling rating (30/60/90 minutes).Choose certified models: ensure testing under appropriate standards.Install by professionals: follow BS-7671 / Part P wiring and building control rules.Plan for insulation: Use fixtures rated for insulation exposure if applicable.Maintain acoustic seal: some units comply with Part E to prevent sound leakage Confirm energy efficiency: LED fixtures often satisfy Part L requirements and are sealed for moisture (Part C compliance)ConclusionFire-rated downlights are not optional—they’re essential components in modern UK buildings to maintain compartmentation and fire safety. By correctly rating, installing, and certifying recessed lighting, you preserve structural fire resistance, comply with Building Regulations (Part B), and protect occupants. Always choose tested products from reputable suppliers and follow professional installation standards like BS-7671. It's a small investment that ensures safety, legality, and peace of mind.Further Reading on Fire Rated DownlightingUnderstanding Fire Rated Downlights (via Astro Lighting)Electrical wiring in the United Kingdom (via Wikipedia)What are Fire Rated Downlights and Where do we Need them? (via SparksDirect)Should every downlight be fire-rated? (via, Professional Electrician)