Ortona Single Matt Black Bathroom Wall Lamp c/w Opal-Glass Globe Shade IP44 G9, Astro 1459005

One of the common questions our customers ask us is related to bathroom lighting, and quite a few of them ask us about IP20-rated lights, and whether they are suitable for use in the bathroom. Are IP20 rated light fittings suitable for use in the bathroom? Can I install an such a light in the bathroom? Questions like these are posed every day, especially since there are some amazing such ceiling lights or wall lamps that the customers really love, and they would like to install them in the bathroom. Let's explore this question together and see what is the correct answer to, Are IP20-rated Lights Suitable for Bathroom Lighting?Note: at Sparks we sell a wide range of IP20 rated lights, IP44 rated light fittings, and IP65 rated lights.IP Rating and Bathroom Zones - Rules and RegulationsWhen installing anything in the bathroom in the UK we need to know the current regulations, which are contained in the 18th Edition Wiring Regs. You may not know them, but it is good to know what wiring regulations apply to installing lights and light fittings in the bathroom, otherwise we put ourselves in great danger, because water and electricity should never mix. Electrical hazards and electrical short circuits due to the mixing of water and electricity should be avoided at any cost since they pose great danger to human life. So what do the wiring regulations say about lighting in the bathroom? The 18th Edition Wiring Regulations define certain bathroom zones - see the image.Note: we have introduced the IP ratings, IP zoning, and Bathroom Zones - see the articles linked. The bathroom zones are three: Zone 0 is the area inside the bathtub or in the shower. There is a lot of splashing water and even more, it can be submerged in water, so special light fittings need to be installed here.Zone 1 is the area above and around the bathtub and the shower, up to 2.25m above the floor. This area is also under the reach of splashing water. Zone 2 is the area of up to 60cm beyond the bathtub edge, basically 60cm outside zone 1. There is some reach of water here, but not as much. The outside zone, the zone outside all these areas, where in general there is no splashing water - some call it "zone 3" while others just call it "the zone outside zones 1 and 2".The current wiring regulations state that specific IP-rated light fittings can be installed in the three zones for the protection of human life. The following IP ratings are recommended:In Zone 0 it is recommended to use IP67, total immersion-proof light fittings, and 12v (low voltage) light fittings are recommended. For our safety, it is not recommended to install any light fitting that is under IPx7 in zone 0.In zone 1 it is recommended to use light fittings having an IP rating of minimum IP45, and IP65 light fittings are warmly recommended in this zone, since water can still reach the light fittings. In zone 2, the area stretching 0.6m outside the perimeter of the bath and up to a height of 2.25 from the floor, it is recommended to use light fittings that have an IP rating of IP44, which are protected from water drops. In the zones outside these three, no IP rating is required, so an IP20-rated fitting can be safely installed. However, for safety reasons, it's best to have IP44-rated light fittings outside of the bathroom zones. IP20 Lights - are they good for the Bathroom?Coming back to our original question, are IP20 rated lights suitable for installation in the bathroom? See the picture above: can this Kymi 220 Plaster Wall Light (Paintable) Ridged Semi-Cylindrical Fitting be installed in the bathroom?Buy the Kymi 220 Plaster Wall Light We may like its finish and shape, but is it safe to be in the bathroom? Based on the current wiring regulations, IP20 rated lights can be installed outside the bathroom zones, that is, away from the reach of splashing or dripping water. Depending on the size of the bathroom, there are many spaces and areas where IP20-rated wall lights or ceiling lights can be installed. These areas are not reached by water jets nor are they at the risk of being splashed or sprinkled with water, so IP20 rated light fittings can safely be installed. However, for the sake of safety, it is best to use IP44-rated lights in the bathroom, even outside the bathroom zones. If you want to be on the safe side, we warmly recommend IP44-rated ceiling lights and wall lamps in the bathroom, outside the bathroom zones. Note: we at Sparks are not qualified to offer professional advice, but we can apply the current regulations and offer advice based on our experience. Before installing any light fitting in the bathroom, please consult with a registered electrician - send them the link to where the light fitting can be viewed, and they will advise. If you are planning to clean the bathroom light fitting with a spray of water or maybe wash it, it is best to have the light fittings rated to a minimum IP65. If there is no reach of splashing water where the light fitting is, and it is outside the bathroom zones defined in the wiring regulations, such lights are suitable. In Conclusion: Always Be Safe in the BathroomIn conclusion, it is entirely up to you when installing IP20 rated lights in the bathroom - outside the bathroom zones. For example, the Ortona Twin Matt Black Bathroom Wall Lamp with Opal-Glass Globe Shades IP44 can safely be used in the bathroom, since it is IP44-rated.Buy the Ortona Twin Matt Black Wall Lamp We would advise staying on the safe side, that is, using IP44-rated light fittings even outside the bathroom zones. You never know, with the steam rising from the bathtub, the vapours of air coming out of the shower, water can reach the light fittings located outside the bathroom zones, and electrical hazards can happen. And whatever you do in the bathroom, always consult a registered electrician to both install and advise on the light fittings you are allowed to install there. 

In today's world, energy efficiency is more critical than ever, and lighting plays a significant role. Lighting consumes a substantial amount of electricity in households and commercial buildings, so choosing the right lighting solution can not only help lower your electricity bills but also reduce your carbon footprint.With so many options available in the market, it can be overwhelming to choose the best energy-efficient lighting solutions for your needs. In this article, we will outline the 5 top lighting tips and solutions that we have found can help you save money, conserve energy and reduce your impact on the environment. These tips are:Invest in LED lighting solutionsKnow your wattage and lumensUse smart lighting for energy efficiencyUse timed lightsKnow the different types of lighting and their impact on energy1. Invest in LED lighting solutionsDespite what you’ve read elsewhere, LEDs still are one of the best energy-efficient lighting solutions you can find on the market.LED (which stands for light-emitting diode) solutions convert almost all the energy they consume into light, with a very little amount wasted. This is in contrast to traditional incandescent bulbs, which convert only about 10% of the energy they consume into light and the remaining 90% wasted as heat.LED lighting solutions also have a longer lifespan than traditional lighting solutions. This means that they need to be replaced less often, reducing the overall amount of energy needed to produce and transport replacement bulbs.LED vs fluorescent light bulbsWhat about fluorescent light bulbs? Aren’t they also energy efficient?Yes, compact fluorescent light bulbs (also known as  CFLs) are also an effective way to conserve energy. But they simply aren’t as efficient as LEDs and, in any case, the drawbacks of CFLs outweigh their benefits.CFLSs take longer to light up and contain a toxic chemical called mercury, which can be dangerous if the bulb breaks. Inhaling mercury has harmful effects on humans and, in the worst cases, can be fatal. If you do use a fluorescent bulb, make sure to dispose of it properly and be careful not to break it.2. Know your wattage and lumensIf you’re going to invest in a lighting solution, it’s important to understand the terminology associated with them.Wattage refers to the unit of power a bulb uses, indicating how much energy it consumes. The higher the wattage, the more energy the bulb consumes.On the other hand, lumens measure the amount of light emitted by a bulb. The higher the number of lumens, the brighter the light. Keep in mind that newer bulbs, like LEDs, are measured in lumens,  whereas incandescent bulbs are typically still measured in watts.Let’s look at an example. An incandescent light bulb may have a label that reads "60W" and "600 Lumens". This means it uses 60 watts of energy to produce a brightness of 600 lumens. However, if an LED bulb is labelled "60W Equivalent, Efficient 9W" and "750 Lumens," this indicates that it consumes only 9 watts of power, but provides an even brighter light than the incandescent bulb. This means that you get better lighting and impact on energy usage.Where can you find the wattage and lumen information of your bulbs? Well, you can find them on your bulb’s packaging (if you haven’t thrown the box out). However, if you no longer have the box, you can buy a new bulb and check the box. Or you can simply look your bulb up online to find the information.Buy Ortona Single Matt Black Bathroom Wall Lamp3. Use smart lighting for energy efficiencyA smart lighting system can be a great way to increase energy efficiency, whether it’s for your home or your business. Below, we’ve outlined three examples of these systems that can help you save on your next power bill. Since most of these methods can be controlled remotely (i.e. you can control your lights from your smartphone or tablet), you can make sure that lights are turned off even when you're not home.Motion sensorsSmart lighting systems can be set up with motion sensors that detect when a room is occupied. This means that lights will automatically turn on when someone enters a room and turn off when the room is empty, ensuring that lights aren't left on unnecessarily and saving energy.By investing in a high-quality occupancy and vacancy detector system, you can conserve energy so that your appliances only activate when people are detected in the vicinity.Geo-fencingGeo-fencing is a type of smart lighting that has a location-based control feature. This automatically turns off your lights once it detects that your smartphone is far away enough from your home.This is an excellent tool to consider, because it can also improve the security of your home or your business by ensuring that lights are turned on when you're arriving and turned off when you leave.DimmersMany smart lighting systems allow you to control the brightness of your lights. By dimming your lights, you can reduce the amount of energy they use while still providing enough light for the task at hand.By investing in a high-quality dimming system, you can effectively replace your light switches entirely and boost your energy savings by up to 65%. Not to mention, dimmers are perfect for customising the ambience in your rooms.4. Use timed lights for energy efficiencyTimed lights are an effective way to improve energy efficiency. By setting a schedule for your home lighting, you can avoid wasting electricity when no one is in a room or during daylight hours.This not only helps you save money on your energy bill but also reduces your carbon footprint. Additionally, timed lights for energy efficiency can provide a sense of security by giving the impression that someone is home, even when you're away. Many smart lighting systems offer easy-to-use scheduling features, allowing you to customise your lighting based on your daily routine.You may also use timed lights to decrease your utility expenses. Some examples of timed lights include:Time Delay Switches. Also referred to as time lag switches, these are able to turn on your appliances for a certain pre-set amount of time, so they can switch off at a time you know you won’t be using it. Plug In Timers. This timer allows you to supply power to a mains-connected deliver at certain times of the day that you choose, allowing you to remain completely controller of your power supply 24/7.All these products help you save power as much as possible, so you never waste the wattage of your precious energy.Buy Zeppo 400 Matt White Pendant5. Know the different types of lighting and their impact on energyLighting and its impact on energy usage are intimately connected, as lighting is one of the major contributors to energy usage. Hence, it's safe to say that improving the efficiency of lighting is crucial for reducing energy consumption.There are four main types of lighting:incandescent,fluorescent, LED, andHalogen lamps.Incandescent bulbsThese are the oldest and least energy-efficient types of bulb. They work by heating a filament to produce light, which results in a lot of wasted energy in the form of heat.In fact, only around 10% of the energy consumed by an incandescent bulb is actually used to produce light, while the remaining energy is wasted as heat.As a result, incandescent bulbs are being phased out in many countries due to their low energy efficiency.Fluorescent bulbsThese are more energy-efficient than incandescent bulbs, but less efficient than LEDs. Fluorescent bulbs work by ionising mercury vapour inside the bulb, which produces ultraviolet light that is then converted into visible light by a phosphorescent coating on the bulb.While they use less energy than incandescent bulbs and have a longer lifespan, they do contain toxic mercury (as mentioned above) and can take longer to turn on and warm up.LED lightingLEDs are by far the most energy-efficient type of bulb and are rapidly gaining popularity due to their energy savings and long lifespan. LEDs work by using a semiconductor to convert electricity into light, with very little energy wasted as heat.LEDs use at least 75% less energy than their incandescent counterparts and may last up to 25 times longer. They can also help you reduce your carbon dioxide emissions by up to 40kg per year.Additionally, LEDs do not contain any toxic materials and can be easily controlled using smart technology to maximise energy efficiency. Using LED smart lighting for energy efficiency is a meaningful, long-term investment that will help you to reduce personal expenses and environmental impact.Halogen lampsHalogen lighting is essentially an enhanced version of incandescent lighting. When it comes to the quality of light emitted, it is just as good as regular incandescent lighting.They are a little more efficient than incandescent bulbs, but not by much. They are still largely inefficient when looking at its lumen-per-watt ratio.From September 2021, halogen light bulbs were banned in the UK. This move was projected to cut 1.26 million tonnes of carbon dioxide in emissions.Looking for an energy-efficient lighting solution?There is no doubt that lighting plays a significant role in energy efficiency. With so many options available in the market, choosing the best energy-efficient lighting solutions can help not only lower electricity bills but also reduce carbon footprint.By making small changes, such as choosing the right bulbs, scheduling lighting, using motion sensors and investing in smart lighting, we can all make a difference in conserving energy, maximising energy efficiency and reducing our impact on the environment.Buy Park Lane Table Lamp Switched in BronzeAt Sparks Direct, we offer a wide range of high-quality energy-efficient lighting solutions, suitable for both homes and businesses. If you need any advice on what solutions are best for you, please don’t hesitate to give us a call. We’re open Monday to Friday, available at 020 7263 8007. We look forward to helping you find the perfect lighting for you!